Wire belts Contact Broschyr Home

Wire belts

Group T

This group consists of narrow-wound belts. Alternate coils wound to the left and to the right bound together by means of grooved cross rods. These belts are used in tunnel ovens in bakeries, among other applications.

pitch of cross rods: 8-20 mm
gauge of coil wire: Ø 1-2 mm
gauge of cross rods: Ø 1,5-3 mm


Type GS

Group G

The belts in this group consists of alternate coils wound to the right and to the left which are joined with crimped cross rods.
The edge of the belt in type GS is formed by the ends of the coil wire and the cross wire being welded together.
In type GB the cross wires are bent, i.e. the cross wires are connected together along the edge of the belt via S-shaped loops. This results in a reinforced, straight belt edge

Type GB
pitch of coils: 4-15 mm
pitch of cross rods: 4,5-25 mm
gauge of coil wire: Ø 1-3 mm
gauge of cross rods: Ø 1-3 mm
 

Einzeln gesponnen

Group V

In this group the coil wires are plaited together and provided with cross wires which are weldedat the edges. These belts are used mainly as conveyor belts in furnaces with high temperatures and high stresses for example hardening furnaces.

Doppelt gesponnen		 pitch of coils: 4-17 mm
pitch of coils: 6-18 mm
gauge of coil wire: Ø 1,5-3 mm
gauge of cross rods: Ø 1,5-4 mm
 
 

KV 32-22/1,5-5

Group K

The belts in this group are open meshed or narrow wound wire belts furnished with chains along the edges. in most cases hollow pin chains are being used but also other types of chains and links are available, as well as side plates and fingers.

KLT Flex 19,05/1,2-5		 Teilung der Ketten: 3/8"-2"
Teilung der Kantenglieder: ¾"-1¼"

OGB 50-2,5-5

OGB 75-20/2,5-5

Gruppe OGB
This type of belt is also called a wire loop belt as the belt consists of bent wire loops which are connected together with cross rods. These belts are manufactured with reinforcement plates at the edges and inside the belt if required. The belt can also be manufactured with fingers and/or high edge plates. The drive wheels or drive rollers have milled grooves where the driving takes place across the full width of the belt with positive driving. In order to increase the opening between the wire loops, the OGB belt can be provided with distance springs or bushes. These belts with open area are used in cooling and drying systems where this is of great advantage as it promotes the circulation of the air.
Standard dimensions:

OGB-Belt with Sideplates		 Pitch Loop Wire Cross rod
30 mm Ø 1,5 mm Ø 4 mm
50 mm Ø 2-2,5 mm Ø 5-7 mm
75 mm Ø 2,5 mm Ø 5 mm
100 mm Ø 3 mm Ø 8 mm
Other dimensions on inquiry

Materials
The material must be chosen on the basis of the environment in which and the temperature at which the belt is to be used.

Steel: Max Working temp C°
Bright/coppered 450 C°
Galvanized
Stainless wire:
SS 2333 (AISI 304) 800 C°
SS 2343 (AISI 316) 800 C°
Heat resistans wire:
253MA 1100 C°
INCOLOY DS 37/18 1100 C°

EX: GS 15-10/1,5-2
EX: GS   a-b     c-d		 a= pitch of cross rods

b= pitch of coils
c= gauge of coil wire
d= gauge of cross rods
 

Adress : Axtorpsvägen 43, 546 72, Mölltorp | Telefon: 0505-30485 Fax 0505-30892 | Epost info@kagebelt.se